Configure Analogue Extensions on Sonus SBC to work with Lync Server 2013


Objective of this article is to guide how to configure Analogue extensions sitting on Sonus SBC 1000\2000 FSX module to communicate with Lync server 2013. Integration with having the FSX modules on the SBC chassis is much less complicated that the FSX is sitting on a different Gateway.

In that case, there will be a licensing concern when it comes to Sonus gateway. To do this, you would probably need Registrar license as well as SIP\Transcoding license. But, in Sonus SBC version 3.1.x does have an option called “RTP Proxy”. This parameter configured in Routing table against the specific route allows RTP to flow without a Transcoding license given that both end use the same codec.

Now back to the subject. The configuration steps would be pretty straight forward,

  • Configure Analogue contact objects in Lync server
  • Configure a CAS Signalling Profile
  • Configure Transformation table
  • Configure a CAS Signalling Group
  • Configure Routing Tables

Configure Analogue contact objects in Lync server

This step is much like configuring a Common Area device. Instead of New-CsCommonAreaDevice, we use New-CsAnalogueDevice. Use the Lync management Shell to run below command. Replace site specific parameters for the highlighted sections.

New-CsAnalogDevice -LineUri tel:+14255556001 -DisplayName “Building 14 Receptionist” -RegistrarPool redmond-Cs-001.litwareinc.com -AnalogFax $False -Gateway 192.168.0.240 -OU “ou=Telecommunications,dc=litwareinc,dc=com

There’s no need to grant a voice policy because the Lync server doesn’t have any sort of authority over the analogue extension.

Configure a CAS Signalling Profile

Jump in to the SBC and navigate in to Settings > CAS. In CAS Signalling Profiles, create a new FSX signalling profile as shown below.CAS Profile

Configure Transformation table 

Transformation Table has to be created so that the numbers coming in to the Analog Extensions and going out to the Lync server are properly normalized. There has to be 2 sets of transformation tables. One set is “To FSX from Lync server” and another set for “To Lync Server from FSX”

To FSX from Lync server

What this rule does is that, a call comes as +6192931234 to 92931234 (The analogue Extension). This rule depends on how the Lync server send the numbers to the SBC. In my case, it’s the full E.164 number. CaptureCapture

To Lync Server from FSX

What this set of rule does is that, It coverts dialed 4 digits Extension numbers in to full E.164 number so that the Lync server can identify where that call to be sent to. CaptureCapture

Configure a CAS Signalling Group

Now to create a Signalling Group for the FSX module. This is where the physical FSX port will get the extension number and get associated with a CAS profile. For the time being, set the Call Routing Table as “Default” since we haven’t created it.  Configure a Signalling group as shown in below snapshot.Untitled picture

Configure Routing Tables

Routing Table is where everything get bonded together. It specifies where the call should go to and which Transformation Tables that it have to use. There gave to be 2 Routing tables. One is “From Lync Server 2013” and another as “From Analog Extensions

From Lync Server

This one specifies where the call to be sent to if it’s coming from lync server. In this instant, “To Analogue Extension“. Configure the routing table as shown in below snapshot.Untitled picture

From Analog Extensions

This one specifies where the call to be sent to if it’s coming from Analogue Extensions. In this instant, “To Lync Server“. Configure the routing table as shown in below snapshot.Untitled picture

Now the configuration is done. Based on this configuration, If a Lync user dials +6192931234, the call will hit on the Analog extension configured as 92321234. And the analogue extension make a call to extension 1212 (Lync User), this will get normalize in to +61892931212 and get forwarded in to Lync Server.

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s